Pulleys wanted
2 posters
Page 1 of 1
Pulleys wanted
by Locknut Tue Oct 30 2018, 08:24
Hi Guys,
I am having a re-think about my Millers Falls power hacksaw set up.I have found out that they were origenally powered in the work shop via a line shaft and I am looking to set a small one up for taking to rallies.
I have 2 old line shaft bearing blocks,a suitable shaft and a flat belt pulley which I can use, but am 2 pulleys short.
I am looking for a 3" v belt pulley for a 1 1/4" shaft and a 6"( 7" would do) v belt one for a 5/8"s shaft ,both shafts do not have keyways - does anyone have spare ones of these please?
Thanks,
Kev.
I am having a re-think about my Millers Falls power hacksaw set up.I have found out that they were origenally powered in the work shop via a line shaft and I am looking to set a small one up for taking to rallies.
I have 2 old line shaft bearing blocks,a suitable shaft and a flat belt pulley which I can use, but am 2 pulleys short.
I am looking for a 3" v belt pulley for a 1 1/4" shaft and a 6"( 7" would do) v belt one for a 5/8"s shaft ,both shafts do not have keyways - does anyone have spare ones of these please?
Thanks,
Kev.
Locknut- A credit to the forum
- Posts : 255
Join date : 2013-02-20
Location : South Devon
Re: Pulleys wanted
by Woodsman Tue Oct 30 2018, 08:48
Sorry Kev - only have flat belt pulleys spare. Will keep my eyes open.
_________________
Regards Paul
Tha can alus tell a Yorkshireman - but tha can't tell him much.
Woodsman- Admin
- Posts : 2699
Join date : 2014-08-24
Age : 73
Location : God's own county
Re: Pulleys wanted
by Locknut Tue Oct 30 2018, 19:22
Hi Paul,
Thanks for that. I am thinking of using the line shaft set up for rallies and for home use using the 15" pulley set up. Those pulleys are out there somewhere its just a matter of locating them!
All the best,
Kev.
Thanks for that. I am thinking of using the line shaft set up for rallies and for home use using the 15" pulley set up. Those pulleys are out there somewhere its just a matter of locating them!
All the best,
Kev.
Locknut- A credit to the forum
- Posts : 255
Join date : 2013-02-20
Location : South Devon
Re: Pulleys wanted
by Woodsman Wed Oct 31 2018, 09:20
Hi Kev,
There's one attached to my Villiers MK40 - but you're not having it
Do you definitely want vintage? Plenty of choice at The Bearing Shop.
There's one attached to my Villiers MK40 - but you're not having it
Do you definitely want vintage? Plenty of choice at The Bearing Shop.
_________________
Regards Paul
Tha can alus tell a Yorkshireman - but tha can't tell him much.
Woodsman- Admin
- Posts : 2699
Join date : 2014-08-24
Age : 73
Location : God's own county
Re: Pulleys wanted
by Locknut Thu Nov 01 2018, 08:24
Hi Paul,
I am looking for vintage at the moment but may have to buy new in the end.I have checked out the Bearing Shop and thats an option for later on.Thanks.
Kev.
I am looking for vintage at the moment but may have to buy new in the end.I have checked out the Bearing Shop and thats an option for later on.Thanks.
Kev.
Locknut- A credit to the forum
- Posts : 255
Join date : 2013-02-20
Location : South Devon
Similar topics» aligning pulleys
» wanted working rs1 mag coil wanted
» machine suppliers (pulleys hoses, bearings fixings etc etc)
» Jap 4/3 wanted
» JAP 4/3 Wanted
» wanted working rs1 mag coil wanted
» machine suppliers (pulleys hoses, bearings fixings etc etc)
» Jap 4/3 wanted
» JAP 4/3 Wanted
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum|
|
|